How To Change The Oil On A 5 Hp Briggs & Stratton Log Splitter

How practice I bank check and change lawn mower oil?

Since there are many components to checking and changing lawn mower oil, we break down:

How to Bank check the Oil Level
How to Change the Oil
How to Locate the Oil Bleed

Warning: Always read the engine and equipment manual(south) before starting, operating, or servicing your engine or equipment to avoid personal injury or property damage. See an authorized dealer or contact Briggs & Stratton if you are unsure of any process or accept boosted questions. Find all Engine Prophylactic Warnings

Checking & Changing Lawn Mower Oil Briggs and Stratton

When you pour fresh oil into the crankcase, information technology'due south a golden or amber colour. Gradually, the estrus, dirt particles and agitated air in the crankcase cause the oil to darken. Dark oil is non only dirty; it has too lost much of its power to glaze and protect engine components.

When to Alter the Oil in Your Small Engine

Every fifty hours of operation or flavour.
For a new snow blower or backyard mower engine, y'all'll also demand to change the oil subsequently the first v hours of performance.
Beyond hours, as well check the oil every time yous use information technology. Dusty/dirty conditions and tough conditions, such every bit wet grass, heavy dust, high temperatures and crude or hilly terrain, may increase the frequency of required oil changes.

The new EXi mower engine doesn't require oil changes, so you lot only need to check and add oil.

How to Check Oil Level

Make it a habit to check the oil level and appearance each time you're about to start a pocket-size engine. Checking the oil while the engine is cold and most of the oil is in the crankcase yields the most accurate reading.

For oil checking procedures on lawnmower applications, please picket our "Checking Engine Oil - Lawnmower Engine" video:

Step 1: Locate the oil fill up cap on the crankcase to start. Make full cap locations vary, depending on the make and model of your engine.

Locate the Oil Fill Cap

On newer models, look for an oil can symbol or the word "oil" or "fill" stamped on the plug.
On small tractors, you may have to lift the hood to locate this cap.
Some engines incorporate either an extended oil fill up tube or a standard make full pigsty with a dipstick for inspection.
Others require you lot to remove the fill cap to check that the oil is at the fill line or the top of the make full hole.

Step two:Make clean the Crankcase: To forbid dirt and debris from falling into the crankcase, use a clean cloth to wipe the area clean before removing the cap.

Clean the Crankcase

Step three:Audit the Oil. If there is no dipstick, dab the oil with a clean tip of the cloth to audit the oil. If the engine includes a dipstick cap,remove the dipstick andwipe information technology with a clean cloth.
- To ensure an accurate reading, reinsert the dipstick completely. If the dipstick cap is a spiral-in type, ensure an accurate reading past screwing in all the mode before removing it to check the level.
- Then, remove information technology again andcheque the oil level.

The oil mark on the dipstick should exist betwixt the lines shown on the dipstick. It should never exist above the FULL line or beneath the Add line.

Inspect the Oil

Changing The Oil on Your Small Engine

After checking the oil level and reading through the Oil Type & Capacity FAQ information technology's time to run the engine for several minutes. Draining the oil while it's warm will carry off many floating particles that would otherwise settle in the engine.

For oil changing procedures on lawnmower applications, please picket our "Changing the Engine Oil - Lawnmower Engine" video:

Stride 1: Stop the engine then disconnect thespark plug leadand secure information technology away from the spark plug. Then, locate the oil bleed plug. On mowers, the plug is typically below the deck and may be obscured by a layer of grass and droppings.

Oil Drain Plug Location

Footstep two: Drain the Oil. Wipe the expanse with a rag to prevent debris from falling into the crankcase when you open the drain plug. Either employ a Briggs & Stratton oil removal kit to remove the oil or exercise it manually.Tilt the mower deck and position some newspaper and an oil pan or jug beneath the mower. Utilise asocket wrench torun the plug counterclockwise, allowing the old oil to bleed. If the plug also serves as a make full cap, it may have two prongs so you can loosen it by paw or utilize a screwdriver or hex key for additional torque.Supercede the drain plug by twisting clockwise and tightening with a box wrench or adjustable wrench.
Step 3: Change the Filter. If your engine has a filter, supervene upon it at least in one case a season, more frequently under heavy use (come across Small Engine Maintenance FAQ).Supplant the oil filter by twisting counter-clockwise on the trunk, using a filter wrench or pipe wrench. Lightlyoil the filter gasketwith clean engine oil. Install new filter rated for your engine.Screw in the filter past mitt until the gasket contact the filter adapter and tighten the filter an additional one/2 to 3/iv turn.

Change Oil Filter

Step iv: Add backyard mower oil to capacity (run into your Operator's Manual). And then, run the engine at idle and check for leaks. Avoid overfilling the crankcase. Too much oil can cause the same type of engine damage as not having enough.
Pace v: Dispose of oil and soiled ragsin accordance with local ecology statutes. In many areas, oil can be left at curbside with other recyclables, provided it is sealed in a recyclable container. Likewise, yous can drop information technology off with a participating Briggs & Stratton service dealer.

Add Lawn Mower Oil

How to Locate the Oil Drain on Your Lawn Mower or Pocket-sized Engine

Rather than tipping your mower to change the oil, yous may utilize the Oil Drain which is very effective, but tin exist difficult to locate on the underside of your mower. Typically, however, on vertical shaft engines, the oil drain plug is located beneath the engine block about the crankshaft.

To remove the square plug, all that is required is a standard size 3/8" ratchet and extension (no socket).

Oil Drain

On horizontal shaft engines it would be located below the centerline of the crankshaft, on the base of the engine cake. Typically an adjustable wrench would remove the square plug.

Oil Drain Location

Please NOTE: Vertical shaft engines, Series 300 to 550, may not feature a bottom oil drain equally shown above. If this is the case, oil must be poured out of the oil fill up tube equally outlined in your engine Operator'southward Manual.

Oil Drain Location